A pipe that splits inside a wall or ceiling turns into a flood in minutes, not hours. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We line up both trades so you are not making five calls while water keeps moving.
Repairs to supply lines fall under plumbing code, which is why we route only to licensed, insured independent plumbers. Ask to see the license on arrival and check it with your state board.
We triage by severity, so active spray and sagging ceilings move to the front of the line. Response is typically fast, though a hard freeze can stretch every schedule in town.
You get a written, flat-rate quote for the repair and any wall access before anything gets cut. You know the number before the first tool comes out.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That narrows the break down to inches instead of tearing out a whole wall to hunt for it.
Freeze breaks, corroded galvanized runs, cracked CPVC fittings, and slab leaks all come through this line. Tell the dispatcher what the pipe looks like and where it runs, and we match you with someone who works on that material every week.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Sealing up a damp cavity is the fastest way to end up with a mold problem by spring.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. Ice expands, pressure builds between the blockage and a closed faucet, and the pipe splits lengthwise, often hours later when it thaws.
Thin-wall Type M copper splits and pins faster than heavier Type L. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX itself flexes, yet the crimp rings and expansion fittings are where freeze damage shows up. CPVC turns brittle with age and heat, and old fittings crack if you so much as bump them.
A hot spot on the floor or a meter that spins with every tap closed points to a slab leak. The plumber locates it with listening gear and a thermal camera, then lays out spot repair versus a reroute.
Galvanized steel rusts from the inside, narrowing flow until a threaded joint finally lets go. Fixing one joint on a corroded system tends to stress the next weakest point.
Braided supply lines under sinks and toilets burst without warning, and they run at full house pressure. A relief valve on the water heater that drips or dumps water needs a look too.
The process is short, and a real person handles each part.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask about the pipe material, the location, and whether any ceiling is sagging.
An independent licensed plumber near you heads over with fittings for copper, PEX, and CPVC on the truck. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The plumber traces the break, often with a thermal camera or acoustic detector, and checks the run for other weak spots. A written, flat-rate quote comes before any drywall is cut.
The permanent repair goes in, the line is pressure tested, and the plumber watches the joint under full pressure before closing anything up. Ask whether their work comes with a written warranty and get it on paper.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Many plumbers still prefer a sweated or press fitting behind drywall, since that joint will sit unseen for decades.
Shut the main and call. We will get a licensed plumber moving your way.
The line in the laundry room's outside wall froze and split the first really cold night. The dispatcher talked me through finding the main, and the plumber replaced the split copper that same morning. He also showed me the Type M pipe and explained why it went first.
The bill jumped and part of the hall floor was warm to bare feet. They found the hot line leaking under the slab with an acoustic detector and a heat camera. We got two written prices, spot repair or reroute, and he explained both without pushing.
Water came through the dining room ceiling from an upstairs bathroom supply line. One call got me a plumber for the line and a separate drying contractor for the ceiling and carpet. Having both lined up from one call saved me a long night of searching.
A tenant in one of my rentals reported a cracked CPVC fitting under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. I got a written quote to replace the whole run and time to think it over.
Close the main shutoff right away and kill power to wet areas at the panel. Open a lower faucet to drain the lines, move valuables, and call so a plumber can head your way.
Turn on the connected faucet and apply gentle heat with a hair dryer or a space heater nearby. Skip the torch entirely, because open flame starts wall fires and can burst the pipe with steam.
They are code-approved in many places, yet a lot of plumbers prefer them only where they stay accessible. Have the plumber explain whether a sweated or press joint is the better long-term choice.
Listening equipment hears the leak, and a thermal camera maps the wet area through the drywall. Together they usually narrow the access hole to a small, patchable opening.
One leak on otherwise healthy pipe is usually a good case for a spot repair. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Drip faucets on exterior walls during deep cold and leave cabinet doors open for heat. Heat tape and foam insulation on crawlspace and attic runs help a lot, and the plumber can point out the worst spots.
We route calls to independent plumbers working all over Boerne, from older neighborhoods with galvanized lines to newer builds plumbed in PEX. Nearby suburbs are covered too, along with zip codes such as 78006.
In the older parts of Boerne, galvanized mains and Type M copper are common, so pinholes and rotted threads are frequent calls. Newer subdivisions lean on PEX and CPVC, where freeze-popped fittings and brittle elbows are the usual story. Wherever you are, tell the dispatcher the age of the house and we match the plumber to the pipe.
Frozen crawlspace pipes, attic runs, and slab leaks across older and newer houses.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
Surrounding towns around Boerne are covered by the same network.
